Tutorial – Page 19 – Replacethatpart.com

How to Replace an Empty Ink Cartridge in the HP DeskJet 3639 All-in-One series Printer – an Illustrated Tutorial in 18 Steps

Make sure you purchase the right ink cartridges for your specific printer and printer region or have your old ones refilled. Cartridges are not compatible between different brands, and often not within the same brand. HP often designs its inkjet hardware to use country-specific consumables. When you unbox a new HP inkjet printer and set it up, you install a set of ink tanks that ship with the printer. As you turn on the device and get ready to use it, an initialization sequence localizes it to the country associated with the ink cartridges you installed. HP recommends that you use original HP ink cartridges.

XL (Extra Large) cartridges cost more but do provide better value in the long run. They will be able to print at least double the pages of a regular cartridge. Our advice is that if you print often, go with XL. However, ink can dry up. So if you are not a frequent printer, go with the regular cartridges.

You can check the estimated ink levels from the printer software or from the printer control panel. Ink level warnings and indicators provide estimates for planning purposes only. When you receive a low-ink warning message, consider having a replacement ink cartridge available to avoid possible printing delays. You do not have to replace the ink cartridges until the print quality is unacceptable.

To check the estimated ink levels from the HP printer control panel:

Ink Alert light
One of the Ink Level icons is blinking with no segment, the Ink Alert light is on, and the Resume light is blinking means: The corresponding ink cartridge is very low on ink.

Ink Level Icons
The left ink icon shows the estimated ink level of the tri-color cartridge, and the right icon shows the estimated ink level of the black cartridge.

To check the ink levels from the HP printer software (Windows):
– Open the HP printer software.
– In the printer software, click the Estimated Ink Levels tab.

Use the single-cartridge mode to operate the HP DeskJet 3637 with only one ink cartridge. The single-cartridge mode is initiated when an ink cartridge is removed from the ink cartridge carriage. Printing with one cartridge might slow the printer and affect the quality of printouts. Therefore, you should replace the empty cartridge as soon as possible.

Which ink cartridges do I need for my HP DeskJet 3637 All-in-One Printer?

For your US HP DeskJet 3637 All-in-One Printer you need HP 63 OR HP 63XL cartridges. Check the price of HP 63 cartridges at Amazon.com .
For your European or UK HP DeskJet 3637 All-in-One Printer you need HP 302 or HP 302XL cartridges.

Try Amazon's ink selector tool to find compatible ink cartridges for your printer.

Replace the ink cartridges

1. Press the power button to turn on the printer, if it is not already on.

2. Load plain white paper in the input tray.
3. Close the output tray extender, and then rotate the output tray clockwise to stow it in the printer

4. Open the front door of the printer.

5. Open the ink cartridge access door. The carriage moves to the center of the printer. Wait until the carriage is idle and silent before you continue.

Remove the old cartridge
6. Lightly press down on one of the old cartridges to release it, and then pull the cartridge toward you out of its slot. Set it aside for recycling. Remove the cartridge from the slot on the left to replace the tri-color cartridge. Remove the cartridge from the slot on the right to replace the black cartridge.

Insert a new cartridge
7. Remove the new cartridge from its package. Be careful to touch only the black plastic on the cartridge.

8. Remove the plastic tape using the pull tab.

Do NOT:
– Remove the copper electrical strip.
– Touch the copper-colored contacts or the ink nozzles.
– Replace the protective tape on the contacts.

9. Hold the ink cartridge by its sides with the nozzles toward the printer, then insert the ink cartridge into its correct slot. Push the ink cartridge forward into its slot until it snaps into place. Repeat these steps to install the other ink cartridge, if necessary. Insert the tri-color ink cartridge into the left slot. Insert the black ink cartridge into the right slot.

10. Close the ink cartridge access door.

11. Close the front door of the printer.

12. Pull out the output tray and the tray extender.

13. Follow any prompts on the computer screen.

Align the cartridges
14. Wait about 30 seconds for the alignment page to automatically print. The printer only prints an alignment page automatically when new ink cartridges are installed. Scanning the alignment page allows the printer to align the ink cartridges and provide the best print quality. If the alignment page fails to automatically print, you can manually print an alignment page using the HP Printer Assistant software (Windows) or the Printer Utility (Mac OS X).
15. Lift the scanner lid.
16. Place the alignment page with the print side down on the right-front corner of the scanner glass. See the engraved guide next to the scanner glass for help loading the alignment page.

17. Close the scanner lid.
18. Press the Start Copy Black button OR the Start Copy Color button on the printer control panel. The printer aligns the ink cartridges.

How to Replace an Empty Ink Cartridge in the HP Officejet 8702 All-in-One series Printer – an Illustrated Tutorial in 7 Steps

HP recommends that you use original HP ink cartridges. XL (Extra Large) cartridges cost more but do provide better value in the long run. They will be able to print at least double the pages of a regular cartridge. Our advice is that if you print often, go with XL. However, ink can dry up. So if you are not a frequent printer, go with the regular cartridges.

You can check the estimated ink levels from the printer software or from the printer control panel. The icon below displays the estimated ink levels. Ink level alerts and indicators provide estimates for planning purposes only. When you receive a low-ink alert, consider having a replacement cartridge available to avoid possible printing delays. You do not have to replace the cartridges until you are prompted to do so. HP recommends that you replace any missing cartridges as soon as possible to avoid print quality issues and possible extra ink usage or damage to the ink system. Never turn off the printer when ink cartridges are missing.

Which ink cartridges do I need for my HP Officejet 8702 All-in-One Printer?

For your US HP OfficeJet 8702 All-in-One Printer you need an HP 952 Black Ink Cartridge AND 3 color cartridges: HP 952 Cyan, HP 952 Magenta and HP 952 Yellow (OR the HP 952 XL versions). There are also Combo Packs (4 cartridges in one pack) available, like the HP 952XL Black and 952 Tri-color (Cyan, Magenta, Yellow) Combo Pack. Check the price of HP 952 cartridges at Amazon.com .

For your European or UK HP OfficeJet 8702 All-in-One Printer you need an HP 953 Black Ink Cartridge AND and 3 color cartridges: HP 953 Cyan, HP 953 Magenta and HP 953 Yellow (OR the HP 953 XL versions). There are also Combo Packs (4 cartridges in one pack) available, like the Hewlett Packard HP Original 953 cartridges 4er Set black, cyan, magenta, yellow Combo Pack.

Try Amazon's ink selector tool to find compatible ink cartridges for your printer.

Replace the ink cartridges

1. Turn the printer on by pressing the power button, if it is not already turned on. Wait until the product is idle and silent before continuing.

Remove the empty cartridge
2. Slip your fingers into the slot on the left side of the printer, and then

3. Find the cartridge you want to replace. Push in on the front of the cartridge to release it, and then pull it toward you to remove it from its slot.

Insert the new cartridge
4. Remove the new ink cartridge from its packaging. Do NOT touch the electrical contacts and ink port.

Do NOT lift the latch handle on the print carriage to install the ink cartridges. Doing so could cause the printhead or ink cartridges to be incorrectly seated, which can cause errors or print quality problems. The latch must remain down in order to correctly install the ink cartridges.

5. Hold the new cartridge so that the cartridge contacts face the printer. Using the color-coded letters for help, slide the ink cartridge into the empty slot until until it clicks into place and it is securely installed in the slot. Make sure that you insert the ink cartridge into the slot that has the same colored letter as the color you are installing.

6. Repeat steps 3 through 5 for each ink cartridge you are replacing.

7. Close the print-carriage access door and wait until the warm-up sequence finishes and your printer is quiet before you proceed.

Align the printhead only if necessary.
Aligning the printhead ensures the high-quality output. The printhead does not have to be realigned when cartridges are replaced. However, you might want to use this feature for print quality issues in printouts where straight lines look wavy or jagged. You can align the printhead from the printer software and from the printer display.

How to Replace the Battery in the FireX Smoke Alarm PADC240 – an Illustrated Tutorial in 19 Steps

Hazards
More accidents happen at home than anywhere else. Replacing the battery of a smoke detector is not without hazards. Make sure you know what you’re doing. The FireX smoke alarm PADC240 is mains-powered and connected to your 110 volt or 220 volt home electrical system. The 9 volt battery only serves as backup in the event of a power failure. Since smoke alarms are placed at ceilings, there’s also a risk of falling. If the battery is not replaced correctly, it might not work properly.

Read our disclaimer
Read the official manual
Hire a qualified electrician if insecure

When is replacement of the battery needed?
The alarm will chirp at random intervals to indicate that the backup battery is running low and needs replacing. However you should replace smoke alarms, when they are ten years old or sooner if they don’t respond properly when tested.

This manual has especially been written for the FireX Smoke Alarm PADC240, but might also be useful for other FireX smoke alarms with a 9V battery back-up, like the I240C and PAD240.

Necessaries
To replace the battery of the FireX Smoke Alarm PADC240, you need:

New high quality, long lasting 9 volt battery, NOT a rechargeable one
Small screwdriver
Step Ladder

Play low battery sound

Replacing the battery

1. Always turn off the electricity. Locate your house’s main electrical panel. Before replacing the battery, turn off main power by removing the appropriate fuse, or switch the circuit breaker that serves the smoke alarm to the off position.

2. Check that the green light on the unit is off. This indicates that the power has been successfully turned off. Other parts of the room or your house might continue to have lights and power.

3. Find the slot for the insertion of the screwdriver to enable you to remove the alarm from the base.

4. Insert the screwdriver into the slot until you feel a slight movement, indicating that the alarm has been disconnected from the base.

5. Grip the whole top of the smoke detector with your hand and turn it about a half inch counterclockwise. This will release it and you can pull it straight off. Some force might be needed, as it doesn’t necessarily come off easily.

6. Carefully unplug the cable without damaging any wired connections. The beige connector plug with the three wires should pull straight out. It’s probably tight but that’s what you need to do to get the battery compartment open. We did NOT have to push, pull or squeeze plastic “catches” or buttons to release the connector plug, but we had to use muscle power. If you can’t get enough grip on the connector plug with your fingers, you might use waterpump pliers to get it off, but do this at your own risk!

7. Use your fingernail to lift the door of the battery compartment open. You do NOT have to use the red button next to the battery door.

8. Remove the old battery from the battery compartment.

9. Gently disconnect and discard the old battery from the 9 volt battery connector. Do this carefully, otherwise you might damage the connector. Apply slight force, but hold the connector, not the wires when you remove it.

10. Connect a new, 9 volt battery to the connector. Use a high quality, long lasting battery. Using rechargeable or low quality batteries may cause your smoke detectors to fail. The 9 volt battery will have two prongs that need to be pushed into place tightly. The battery will fit only one way. Be sure the battery connector is securely attached to the battery terminals.

11. Place the new and connected battery into the battery compartment.

12. Close the battery compartment door. Push down until it snaps into place. You do NOT have to use screws.

13. Now your smoke alarm is on your table, you might want to use this opportunity to remove possible dust from the inside and outsight of the smoke alarm, using a (handheld) vacuum cleaner. To clean the housing, wipe it down with a dry microfiber cloth.

14. Press and hold the test button. The alarm will sound if the battery is properly connected and working. DO NOT use any other test method.

Play test sound

15. Replace the beige connector plug. Push firmly until the connector snaps into place with a click. Gently tug the connector to be sure it is attached properly.

16. Push the wires back into the ceiling if necessary and reattach the smoke alarm to the mounting plate by turning smoke alarm clockwise until it snaps into place.

17. Turn the electricity back on.

18. Ensure that the green light is showing on the unit. This indicates that the alarm is connected correctly to the main supply.

19. Press and hold the test button once again. The alarm will sound if the smoke alarm is properly connected and working. DO NOT use any other test method.

Play test sound

If the green light on the unit is on and the test sound works, you’ve successfully replaced the battery of your Firex smoke alarm. Congratulations! Your FireX smoke alarm will guard you for years to come!

How to Replace an Empty Ink Cartridge in the HP Officejet Pro L7680 All-in-One series – an Illustrated Tutorial in 8 Steps

You can check the estimated ink levels from the printer control-panel, from the printer Toolbox, and the embedded Web server (EWS).

A. To check the estimated ink levels from the display.
The color display of the HP Officejet Pro L7680 shows ink level icons at the bottom of the display. The color of the icon corresponds to the color of the ink cartridge, and the fill level of the icon corresponds to the fill level of the ink cartridge.

B. To check the estimated ink levels from the printer Toolbox (Windows).
– Open the Toolbox: From the HP Solution Center, click the Settings menu, point to Print Settings, and then click Printer Toolbox.
– Click the Estimated Ink Levels tab to view the inklevel information, and then scroll to display the Cartridge Details button. Click the Cartridge Details button to view information about replacement ink cartridges.
C. To check the estimated ink levels from the embedded Web server.
The embedded Web server contains pages that you can use to view product information and change device settings. The pages also contain links to other e-services. The Information page shows status information about the device, its ink supplies and usage, and a log of device events (such as errors).

Ink level warnings and indicators provide estimates for planning purposes only. Consider getting replacement print cartridges when you receive a low-ink warning message. This avoids possible printing delays. You do not need to replace the print cartridges until print quality becomes unacceptable.

Which ink cartridges do I need for my HP Officejet Pro L7680 All-in-One Printer?

For your US, European and UK HP Officejet Pro L7680 All-in-One Printer you need HP 88 Black (OR HP 88XL Black) AND 3 color cartridges: HP 88 Cyan, HP 88 Magenta and HP 88 Yellow (OR the XL-versions). There are also Combo Packs (3 cartridges in one pack) available, like the HP 88XL Value Combo Pack Cyan Magenta and Yellow High Yield Original Ink.

Try Amazon's ink selector tool to find compatible ink cartridges for your printer.

Replace the ink cartridges

1. Press the power button to turn on the printer, if it is not already on. Wait until the product is idle and silent before continuing. When the device is turned on for the first time, it takes approximately 12 minutes to initialize it after the printheads are installed.

2. Load plain unused Letter or A4 white paper in the input tray.

Remove the old cartridge
3. Gently pull open the ink cartridge cover.

4. Remove the ink cartridge that requires replacement by grasping it between your thumb and forefinger and pulling it firmly toward you.

Note: Your HP Officejet Pro L7680 All-in-One printer may not look exactly like the picture below, but the cartridge numbers and cartridge system are the same.

(Please wait for the video to load)

Insert a new cartridge
5. Remove the new ink cartridge from its package. Be careful to touch only the plastic on the cartridge. Do NOT touch the electrical contacts and ink port.

6. Hold the cartridge by its sides with the nozzle toward the product, and then insert the cartridge into its color-coded slot. Press the cartridge forward into the slot until it snaps into place. Press down firmly on the cartridge to ensure proper contact.

7. If more than one cartridge is low on ink, repeat the steps to insert the other cartridges.
8. Close the ink cartridge cover.

(Please wait for the video to load)

Align the printhead only if necessary.
Whenever you replace a cartridge or printhead, the device automatically aligns the printheads to ensure the best print quality. However, if the appearance of your printed pages indicates that the printheads are misaligned, you can start the alignment process manually. You can align the printhead from the printer control panel, from the HP printer software and from the embedded web server (EWS).
– Control panel: Press the Setup button, select Tools, select Align Printer, and then press OK. Press OK when the alignment is done to continue.
– Embedded Web server (EWS): Click the Settings tab, click Device Services in the left pane, select Align Printheads from the drop-down list in the Print Quality section, and then click Run Diagnostic.
– Toolbox (Windows): Click the Services tab, and then click Align Printheads and follow the onscreen instructions.