Printer – Page 15 – Replacethatpart.com

How to Replace an Empty Ink Cartridge in the HP DeskJet 3639 All-in-One series Printer – an Illustrated Tutorial in 18 Steps

Make sure you purchase the right ink cartridges for your specific printer and printer region or have your old ones refilled. Cartridges are not compatible between different brands, and often not within the same brand. HP often designs its inkjet hardware to use country-specific consumables. When you unbox a new HP inkjet printer and set it up, you install a set of ink tanks that ship with the printer. As you turn on the device and get ready to use it, an initialization sequence localizes it to the country associated with the ink cartridges you installed. HP recommends that you use original HP ink cartridges.

XL (Extra Large) cartridges cost more but do provide better value in the long run. They will be able to print at least double the pages of a regular cartridge. Our advice is that if you print often, go with XL. However, ink can dry up. So if you are not a frequent printer, go with the regular cartridges.

You can check the estimated ink levels from the printer software or from the printer control panel. Ink level warnings and indicators provide estimates for planning purposes only. When you receive a low-ink warning message, consider having a replacement ink cartridge available to avoid possible printing delays. You do not have to replace the ink cartridges until the print quality is unacceptable.

To check the estimated ink levels from the HP printer control panel:

Ink Alert light
One of the Ink Level icons is blinking with no segment, the Ink Alert light is on, and the Resume light is blinking means: The corresponding ink cartridge is very low on ink.

Ink Level Icons
The left ink icon shows the estimated ink level of the tri-color cartridge, and the right icon shows the estimated ink level of the black cartridge.

To check the ink levels from the HP printer software (Windows):
– Open the HP printer software.
– In the printer software, click the Estimated Ink Levels tab.

Use the single-cartridge mode to operate the HP DeskJet 3637 with only one ink cartridge. The single-cartridge mode is initiated when an ink cartridge is removed from the ink cartridge carriage. Printing with one cartridge might slow the printer and affect the quality of printouts. Therefore, you should replace the empty cartridge as soon as possible.

Which ink cartridges do I need for my HP DeskJet 3637 All-in-One Printer?

For your US HP DeskJet 3637 All-in-One Printer you need HP 63 OR HP 63XL cartridges. Check the price of HP 63 cartridges at Amazon.com .
For your European or UK HP DeskJet 3637 All-in-One Printer you need HP 302 or HP 302XL cartridges.

Try Amazon's ink selector tool to find compatible ink cartridges for your printer.

Replace the ink cartridges

1. Press the power button to turn on the printer, if it is not already on.

2. Load plain white paper in the input tray.
3. Close the output tray extender, and then rotate the output tray clockwise to stow it in the printer

4. Open the front door of the printer.

5. Open the ink cartridge access door. The carriage moves to the center of the printer. Wait until the carriage is idle and silent before you continue.

Remove the old cartridge
6. Lightly press down on one of the old cartridges to release it, and then pull the cartridge toward you out of its slot. Set it aside for recycling. Remove the cartridge from the slot on the left to replace the tri-color cartridge. Remove the cartridge from the slot on the right to replace the black cartridge.

Insert a new cartridge
7. Remove the new cartridge from its package. Be careful to touch only the black plastic on the cartridge.

8. Remove the plastic tape using the pull tab.

Do NOT:
– Remove the copper electrical strip.
– Touch the copper-colored contacts or the ink nozzles.
– Replace the protective tape on the contacts.

9. Hold the ink cartridge by its sides with the nozzles toward the printer, then insert the ink cartridge into its correct slot. Push the ink cartridge forward into its slot until it snaps into place. Repeat these steps to install the other ink cartridge, if necessary. Insert the tri-color ink cartridge into the left slot. Insert the black ink cartridge into the right slot.

10. Close the ink cartridge access door.

11. Close the front door of the printer.

12. Pull out the output tray and the tray extender.

13. Follow any prompts on the computer screen.

Align the cartridges
14. Wait about 30 seconds for the alignment page to automatically print. The printer only prints an alignment page automatically when new ink cartridges are installed. Scanning the alignment page allows the printer to align the ink cartridges and provide the best print quality. If the alignment page fails to automatically print, you can manually print an alignment page using the HP Printer Assistant software (Windows) or the Printer Utility (Mac OS X).
15. Lift the scanner lid.
16. Place the alignment page with the print side down on the right-front corner of the scanner glass. See the engraved guide next to the scanner glass for help loading the alignment page.

17. Close the scanner lid.
18. Press the Start Copy Black button OR the Start Copy Color button on the printer control panel. The printer aligns the ink cartridges.

How to Replace an Empty Ink Cartridge in the HP OfficeJet Pro 8035 series – an Illustrated Tutorial in 11 Steps

HP recommends that you use original HP ink cartridges. XL (Extra Large) cartridges cost more but do provide better value in the long run. They will be able to print at least double the pages of a regular cartridge. Our advice is that if you print often, go with XL. However, ink can dry up. So if you are not a frequent printer, go with the regular cartridges.

You can check the estimated ink levels from the printer control panel or from the printer software. Ink level warnings and indicators provide estimates for planning purposes only. When you receive a low-ink warning message, consider having a replacement cartridge available to avoid possible printing delays. You do not have to replace the cartridges until prompted to do so.

To check the estimated ink levels from the printer control panel:
– touch or swipe down the tab at the top of the screen to open the Dashboard, and then touch the Ink Icon (see below) to check the estimated ink levels.

Which ink cartridges do I need for my HP OfficeJet Pro 8035 printer?

For your US HP OfficeJet Pro 8035 printer you need 1 HP 910 Black OR the XL-version HP 910XL Black AND 3 color cartridges: HP 910 Cyan/Magenta/Yellow OR the XL-version HP 910XL Cyan/Magenta/Yellow. There are also Combo Packs (4 cartridges in one pack) available, like the HP 910 | 4 Ink Cartridges | Black, Cyan, Magenta, Yellow | 3YL61AN, 3YL58AN, 3YL59AN, 3YL60AN. Check the price of HP 910 cartridges at Amazon.com .

For your European or UK HP OfficeJet Pro 8035 printer you need 1 HP 912 Black OR the XL-version HP 912XL Black cartridge AND 3 color cartridges: HP 912 Cyan + HP 912 Magenta + HP 912 Yellow cartridges. OR the XL-version of the color cartridges: HP 912XL Cyan + HP 912XL Magenta + HP 912XL Yellow. There are also Combo Packs (4 cartridges in one pack) available, like the HP 3YP34AE 912XL High Yield Original Ink Cartridge, Black/Cyan/Magenta/Yellow, Pack of 4.

Try Amazon's ink selector tool to find compatible ink cartridges for your printer.

Replace the ink cartridges.

1. Look at the Power button located on the printer. If it is not lit, the printer is turned off. Press the Power button to turn on the printer. Wait until the product is idle and silent before continuing.

Remove the old cartridge
2. Open the front door.

3. Open the cartridge access door. Wait until the carriage is idle and silent before you proceed.

4. Press the tab on the front of the cartridge inward to release it, and then pull up on the cartridge to remove it from the slot.

Insert the new cartridge
5. Remove the new ink cartridge from its packaging by pulling the orange pull-tab straight back to remove the plastic wrap from the ink cartridge. Make sure you remove the orange pull-tab completely. When you remove the plastic wrap, the paper label on the top of the cartridge tears slightly, which is necessary to vent the cartridge. Do not touch the copper-colored electrical contacts and ink port.

6. Remove the orange cap from the cartridge. Hold the ink cartridge by its sides, and then twist the cap counter-clockwise until it snaps off. A forceful twist may be required to remove the cap.

7. Gently bend the tab away from the ink cartridge. Be careful not to bend the tab out more than 1.27 cm (0.5 in). Moving the tab too far might damage the ink cartridge or cause the tab to break.

8. Hold the ink cartridge so that the ink cartridge contacts are facing down and toward the printer. Match the colored dot on the ink cartridge with the dot of the same color on the carriage. Slide the new ink cartridge into its slot, and then gently press the ink cartridge down until it clicks into place and is seated firmly in the slot. Make sure that the color-coded letter on the cartridge matches that on the slot.

9. Repeat step 3 to 7 for each ink cartridge you are replacing.

10. Close the ink cartridge access door.

11. Close the front door.

Align the printhead only if necessary.
The printer automatically aligns the printhead during the initial setup. The printhead does not have to be realigned when cartridges are replaced. However, you might want to use this feature for print quality issues in printouts where straight lines look wavy or jagged. You can align the printhead from the printer display and from the HP printer software.

How to Replace an Empty Ink Cartridge in the HP OfficeJet Pro 8025 series – an Illustrated Tutorial in 11 Steps

Which ink cartridges do I need for my HP OfficeJet Pro 8025 printer?

For your US HP OfficeJet Pro 8025 printer you need 1 HP 910 Black OR the XL-version HP 910XL Black AND 3 color cartridges: HP 910 Cyan/Magenta/Yellow OR the XL-version HP 910XL Cyan/Magenta/Yellow. There are also Combo Packs (4 cartridges in one pack) available, like the HP 910 | 4 Ink Cartridges | Black, Cyan, Magenta, Yellow | 3YL61AN, 3YL58AN, 3YL59AN, 3YL60AN. Check the price of HP 910 cartridges at Amazon.com .

For your European or UK HP OfficeJet Pro 8025 printer you need 1 HP 912 Black OR the XL-version HP 912XL Black cartridge AND 3 color cartridges: HP 912 Cyan + HP 912 Magenta + HP 912 Yellow cartridges. OR the XL-version of the color cartridges: HP 912XL Cyan + HP 912XL Magenta + HP 912XL Yellow. There are also Combo Packs (4 cartridges in one pack) available, like the HP 3YP34AE 912XL High Yield Original Ink Cartridge, Black/Cyan/Magenta/Yellow, Pack of 4.

Try Amazon's ink selector tool to find compatible ink cartridges for your printer.

Replace the ink cartridges.

Remove the old cartridge
2. Open the front door.

3. Open the cartridge access door. Wait until the carriage is idle and silent before you proceed.

4. Press the tab on the front of the cartridge inward to release it, and then pull up on the cartridge to remove it from the slot.

6. Remove the orange cap from the cartridge. Hold the ink cartridge by its sides, and then twist the cap counter-clockwise until it snaps off. A forceful twist may be required to remove the cap.

7. Gently bend the tab away from the ink cartridge. Be careful not to bend the tab out more than 1.27 cm (0.5 in). Moving the tab too far might damage the ink cartridge or cause the tab to break.

9. Repeat step 3 to 8 for each ink cartridge you are replacing.

10. Close the ink cartridge access door.

11. Close the front door.

How to Replace an Empty Ink Cartridge in the HP Officejet Pro L7680 All-in-One series – an Illustrated Tutorial in 8 Steps

You can check the estimated ink levels from the printer control-panel, from the printer Toolbox, and the embedded Web server (EWS).

A. To check the estimated ink levels from the display.
The color display of the HP Officejet Pro L7680 shows ink level icons at the bottom of the display. The color of the icon corresponds to the color of the ink cartridge, and the fill level of the icon corresponds to the fill level of the ink cartridge.

B. To check the estimated ink levels from the printer Toolbox (Windows).
– Open the Toolbox: From the HP Solution Center, click the Settings menu, point to Print Settings, and then click Printer Toolbox.
– Click the Estimated Ink Levels tab to view the inklevel information, and then scroll to display the Cartridge Details button. Click the Cartridge Details button to view information about replacement ink cartridges.
C. To check the estimated ink levels from the embedded Web server.
The embedded Web server contains pages that you can use to view product information and change device settings. The pages also contain links to other e-services. The Information page shows status information about the device, its ink supplies and usage, and a log of device events (such as errors).

Ink level warnings and indicators provide estimates for planning purposes only. Consider getting replacement print cartridges when you receive a low-ink warning message. This avoids possible printing delays. You do not need to replace the print cartridges until print quality becomes unacceptable.

Which ink cartridges do I need for my HP Officejet Pro L7680 All-in-One Printer?

For your US, European and UK HP Officejet Pro L7680 All-in-One Printer you need HP 88 Black (OR HP 88XL Black) AND 3 color cartridges: HP 88 Cyan, HP 88 Magenta and HP 88 Yellow (OR the XL-versions). There are also Combo Packs (3 cartridges in one pack) available, like the HP 88XL Value Combo Pack Cyan Magenta and Yellow High Yield Original Ink.

Try Amazon's ink selector tool to find compatible ink cartridges for your printer.

Replace the ink cartridges

1. Press the power button to turn on the printer, if it is not already on. Wait until the product is idle and silent before continuing. When the device is turned on for the first time, it takes approximately 12 minutes to initialize it after the printheads are installed.

2. Load plain unused Letter or A4 white paper in the input tray.

Remove the old cartridge
3. Gently pull open the ink cartridge cover.

4. Remove the ink cartridge that requires replacement by grasping it between your thumb and forefinger and pulling it firmly toward you.

Note: Your HP Officejet Pro L7680 All-in-One printer may not look exactly like the picture below, but the cartridge numbers and cartridge system are the same.

(Please wait for the video to load)

Insert a new cartridge
5. Remove the new ink cartridge from its package. Be careful to touch only the plastic on the cartridge. Do NOT touch the electrical contacts and ink port.

6. Hold the cartridge by its sides with the nozzle toward the product, and then insert the cartridge into its color-coded slot. Press the cartridge forward into the slot until it snaps into place. Press down firmly on the cartridge to ensure proper contact.

7. If more than one cartridge is low on ink, repeat the steps to insert the other cartridges.
8. Close the ink cartridge cover.

(Please wait for the video to load)

Align the printhead only if necessary.
Whenever you replace a cartridge or printhead, the device automatically aligns the printheads to ensure the best print quality. However, if the appearance of your printed pages indicates that the printheads are misaligned, you can start the alignment process manually. You can align the printhead from the printer control panel, from the HP printer software and from the embedded web server (EWS).
– Control panel: Press the Setup button, select Tools, select Align Printer, and then press OK. Press OK when the alignment is done to continue.
– Embedded Web server (EWS): Click the Settings tab, click Device Services in the left pane, select Align Printheads from the drop-down list in the Print Quality section, and then click Run Diagnostic.
– Toolbox (Windows): Click the Services tab, and then click Align Printheads and follow the onscreen instructions.