How-to-Guide: Upgrade RAM Memory of the HP Mini 210 Netbook – a Complete Tutorial

Adding RAM is often the most cost-effective upgrade you can make to speed up a computer. When a computer runs short of RAM, it’s forced to swap the overflow data on and off of the hard drive, which can significantly slow performance. Fortunately, upgrading netbook memory is often one of the easiest computer upgrades. Do you want to get a little more power out of your HP Mini 210 Netbook Pine Trail powered Netbook? Upgrade that 1GB memory module with a 2GB SODIMM. It will speed up opening new applications, running multiple applications at once, and switching between software applications (multi-tasking). Here’s a complete and easy guide on how to upgrade your HP Mini 210 Netbook’s memory.

Purchase the right memory.

Intel Atom N450 (Pineview) based machines can’t access more than 2GB of RAM in total. A 1GB memory module is installed in the memory slot inside your computer. There is, however, only one memory slot on the motherboard, so this means that you’ll have to remove the current RAM module in order to insert a new one. For your HP Mini 210 Netbook you need a standard 200 pin DDR2 SODIMM laptop memory module (not desktop memory). Select a 2GB DDR2 SODIMM memory module of 667MHz or 800MHz. These may be referenced as PC2-5400 or PC2-6400. HP recommends a 667MHz SODIMM. A faster 800MHz stick will also work, but it won’t make a difference in speed as it’s just throttled down to the motherboard bus speed of 667MHz. Recommended memory brands include, but are not limited to, Crucial, Corsair, Kingston, Patriot, Hynix and Viking.

(#ad or paid links)

  • Crucial 2GB Single DDR2 667MHz (PC2-5300) CL5 SODIMM 200-Pin Notebook Memory Module CT25664AC667
    This is by far the most popular Netbook memory replacement at the moment.
  • Crucial 2GB Single DDR2 800MHz (PC2-6400) CL6 SODIMM 200-Pin Notebook Memory Module CT25664AC800
  • Corsair VS2GSDS667D2 2GB (1x2GB) DDR2 667 MHz (PC2 5300) Laptop Memory
  • The computer has one memory module compartment, which is located on the bottom of the computer,
    beneath the removable bottom panel. There is, however, only one memory slot on the motherboard so this means that you’ll have to remove the current RAM module in order to insert a new one. The procedure to replace the memory is described below.

    1. Shut down your Netbook completely.

    2. Disconnect all external devices connected to your HP Mini 210.

    3. Power off your Mini 210 if it’s on. Also, unplug the AC power adapter.

    4. Prepare your Mini 210 by placing it upside-down on a flat surface with some form of soft padding. Static electricity can damage your module and other computer parts. Make sure that you are working in a static-safe environment. Remove any plastic bags or papers from your work space.

    5. Remove the battery. This will prevent you from accidentally shorting anything on the system board during this process.
    a) Slide the battery release latches (1) to release the battery.
    b) Remove the battery (2) from the computer.

    6. Discharge residual power by pressing the power button.

    7. If your device has WWAN capability, remove the SIM (select models only).
    a) Press in on the SIM. The module is partially ejected from the SIM slot.
    b) Remove the SIM from the SIM slot.

    8. Electrostatic discharge (ESD) can damage electronic components, so be sure to ground yourself. Touch a large or grounded piece of metal (like a tap) for a couple of seconds and you should be fine.

    9. Remove the bottom panel:
    a. Press the inner release latches (2) on the left and right sides to loosen the bottom panel.
    b. Pull away the bottom panel (3).

    10.
    a) Pull away the retention clips (1) on each side of the memory module. The memory module tilts up.
    b) Grasp the edge of the memory module (2), and gently pull the module out of the memory module slot at an angle.

    11. Most memory will be sold in a piece of hard, clear plastic. Gently remove the new module from the packaging by pressing on it from the plastic side. Avoid bending the module or applying too much force to the packaging. When you remove the SODIMM memory module from its packaging hold it by the edges, try not to touch the gold colored contacts as this can damage the memory.

    12. Insert a new memory module:
    a) Align the notched edge (1) of the memory module with the tab in the memory module slot.
    b) With the memory module at a 45-degree angle from the surface of the memory module
    compartment, press the module (2) into the memory module slot until it is seated.
    c) Gently press the memory module (3) down, applying pressure to the left and right edges of
    the memory module, until the retention clips snap into place. Make sure the memory module is completely fixed. If the memory does not fit easily, push the memory module down while puling the memory module latches outward. The module should be seated so that you don’t see any of the gold contacts.

    13. Replace the removable bottom panel:
    a. With the battery bay away from you, position the bottom panel at a 45–degree angle from the
    surface of the computer so that the tabs on the underside of the panel align with the matching
    slots on the computer (1).
    b. Gently press the bottom panel (2) down, applying pressure to both the left and right edges of
    the panel, until it snaps into place.

    14. Insert your 3G SIM card if you have one.

    15. Test it. To install the battery again, slide the battery into the system. Turn your computer back on. The BIOS automatically detects the amount of memory in the system and configures CMOS accordingly during the Power-On Self-Test (POST) process. There is no hardware or software (including BIOS) setup required after the memory is installed. You should see the new amount of memory displayed on your start-up screens or in the properties for “My Computer”. Right click on the “My Computer” icon and select “properties”. The screen which appears should show approximately 2GB of RAM. The memory capacity reported in Windows might be less than the actual capacity of memory. This is because BIOS or the onboard graphics uses a portion of memory or claims it for further use. You can also Hold F10 during start-up. The BIOS Setup Utility screen will open and the System Memory item shows the total amount of memory installed in your netbook. If you have any problems, go to step 16 for troubleshooting tips.

    16. Troubleshooting. If you have trouble with your new RAM, check these things first. Check the power cords. Is everything plugged in properly? Check the module. Did both side clips snap to hold the module firmly in place? Try removing the module and replacing it to make sure it is seated properly in the slot. If you’re still having difficulties with your RAM, check the Crucial FAQ section. You may find an easy solution for your problem.

    Enjoy!

How to Upgrade RAM Memory of the Fujitsu LifeBook MH380 Pine Trail Netbook – a Complete Guide

Adding RAM is often the most cost-effective upgrade you can make to speed up a computer. When a computer runs short of RAM, it’s forced to swap the overflow data on and off of the hard drive, which can significantly slow performance. Fortunately, upgrading netbook memory is often one of the easiest computer upgrades. Do you want to get a little more power out of your Fujitsu LifeBook MH380 Pine Trail powered Netbook? Upgrade that 1GB memory module with a 2GB SODIMM. It will speed up opening new applications, running multiple applications at once, and switching between software applications (multi-tasking). Here’s a complete and easy guide on how to upgrade your Fujitsu LifeBook MH380’s memory.

Purchase the right memory.

Intel Atom N450 (Pineview) based machines can’t access more than 2GB of RAM in total. A 1GB memory module is installed in the memory slot at the bottom of your computer. There is, however, only one memory slot on the motherboard, so this means that you’ll have to remove the current RAM module in order to insert a new one. For your Fujitsu LifeBook MH380 Netbook you need a standard 200 pin DDR2 SODIMM laptop memory module (not desktop memory). Select a 2GB DDR2 SODIMM memory module of 800MHz or 667MHz. These may be referenced as PC2-6400 or PC2-5400. The 800MHz stick will work, but it won’t make a difference in speed as it’s just throttled down to the motherboard bus speed of 667MHz. Recommended brands include, but are not limited to, Crucial, Corsair, Kingston, Patriot, Hynix and Viking.

(#ad or paid links)

  • Crucial 2GB Single DDR2 667MHz (PC2-5300) CL5 SODIMM 200-Pin Notebook Memory Module CT25664AC667
    This is by far the most popular Netbook memory replacement at the moment.
  • Crucial 2GB Single DDR2 800MHz (PC2-6400) CL6 SODIMM 200-Pin Notebook Memory Module CT25664AC800
  • Corsair VS2GSDS667D2 2GB (1x2GB) DDR2 667 MHz (PC2 5300) Laptop Memory
  • A 1GB memory module is installed in the memory slot at the bottom of your computer. There is, however, only one memory slot on the motherboard so this means that you’ll have to remove the current RAM module in order to insert a new one. The procedure to replace the memory is described below.

    1. Shut down your Netbook completely.

    2. Disconnect all external devices connected to your Fujitsu LifeBook MH380.

    3. Power off your MH380 if it’s on. Also, unplug the AC power adapter.

    4. Prepare your Netbook by placing it upside-down on a flat surface with some form of soft padding. Static electricity can damage your module and other computer parts. Make sure that you are working in a static-safe environment. Remove any plastic bags or papers from your work space.

    5. Remove the battery. This will prevent you from accidentally shorting anything on the system board during this process.
    Slide the left battery release latch (labeled “1 HOLD”) to the left and hold it.
    Slide the right battery latch (labeled “2”) to the right.
    While continuing to hold the left battery latch, slide the battery out of the battery compartment and remove it.

    6. Discharge residual power by pressing the power button.

    7. Be sure to ground yourself. Touch a large piece of metal or grounded metal (like a tap) for a couple of seconds and you should be fine.

    8. Loosen the 2 captive screws that secures the memory module compartment cover to the computer.

    9. Spread the retaining tabs on each side of the memory module slot to release the memory module. (The edge of the module opposite the slot rises away from the device). Remove the memory module by pulling the module away from the slot at an angle.

    10. Most memory will be sold in a piece of hard, clear plastic. Gently remove the new module from the packaging by pressing on it from the plastic side. Avoid bending the module or applying too much force to the packaging. When you remove the SODIMM memory module from its packaging hold it by the edges, try not to touch the gold colored contacts as this can damage the memory.

    11. Insert a new memory module into the memory slot at an angle of approximately 45 degrees aligning it to the angle of the memory slot. Memory modules are designed with a notch to prevent incorrect insertion into the memory module slot.

    12. Press the connector edge of the module firmly down and into the connector until it lodges under the retaining clip. You will hear a click when it is properly in place. If the memory does not fit easily, push the memory module down while puling the memory module latches outward. The module should be seated so that you don’t see any of the gold contacts.

    13. Before you close your case, replace the battery. Slide the battery into the compartment; the left battery release latch will click into place. Slide the right battery latch to the left to lock it.

    14. Test it.
    Turn your computer back on. The BIOS automatically detects the amount of memory in the system and configures CMOS accordingly during the Power-On Self-Test (POST) process. There is no hardware or software (including BIOS) setup required after the memory is installed. You should see the new amount of memory displayed on your start-up screens or in the properties for “My Computer”. The screen which appears should show approximately 2GB of RAM. The memory capacity reported in Windows is less than the actual capacity of memory. This is because BIOS or the onboard graphics uses a portion of memory or claims it for further use.

    You can also hold <F2> during the POST. When the Fujitsu logo appears on the booting screen, press the <F2> key to enter the BIOS Setup. The BIOS Setup Utility screen will open and the System Memory item shows the total amount of memory installed in your netbook. If everything works correctly, you are done and you can close your case. If you have any problems, go to step 15 for troubleshooting tips.

    15. Troubleshooting. If you have trouble with your new RAM, check these things first. Check the power cords. Is everything plugged in properly? Check the module. Did both side clips snap to hold the module firmly in place? Try removing the module and replacing it to make sure it is seated properly in the slot. If you’re still having difficulties with your RAM, check the Crucial FAQ section. You may find an easy solution for your problem.

    16. Close the memory compartment cover and fasten the screw.

    Enjoy!

How to Upgrade RAM Memory of the Samsung N315 Pine Trail Netbook – a Complete Guide

Adding RAM is often the most cost-effective upgrade you can make to speed up a computer. When a computer runs short of RAM, it’s forced to swap the overflow data on and off of the hard drive, which can significantly slow performance. Fortunately, upgrading netbook memory is often one of the easiest computer upgrades. Do you want to get a little more power out of your Samsung N315 Pine Trail powered Netbook? Upgrade that 1GB memory module with a 2GB SODIMM. It will speed up opening new applications, running multiple applications at once, and switching between software applications (multi-tasking). Here’s a complete and easy guide on how to upgrade your Samsung N315’s memory.

Purchase the right memory.

Intel Atom N450 (Pineview) based machines can’t access more than 2GB of RAM in total. A 1GB memory module is installed in the memory slot at the bottom of your computer. There is, however, only one memory slot on the motherboard, so this means that you’ll have to remove the current RAM module in order to insert a new one. For your Samsung N315 Netbook you need a standard 200 pin DDR2 SODIMM laptop memory module (not desktop memory). Select a 2GB DDR2 SODIMM memory module of 800MHz or 667MHz. These may be referenced as PC2-6400 or PC2-5400. The 800MHz stick will work, but it won’t make a difference in speed as it’s just throttled down to the motherboard bus speed of 667MHz. Recommended brands include, but are not limited to, Crucial, Corsair, Kingston, Patriot, Hynix and Viking.

(#ad or paid links)

  • Crucial 2GB Single DDR2 667MHz (PC2-5300) CL5 SODIMM 200-Pin Notebook Memory Module CT25664AC667
    This is by far the most popular Netbook memory replacement at the moment.
  • Crucial 2GB Single DDR2 800MHz (PC2-6400) CL6 SODIMM 200-Pin Notebook Memory Module CT25664AC800
  • Corsair VS2GSDS667D2 2GB (1x2GB) DDR2 667 MHz (PC2 5300) Laptop Memory
  • A 1GB memory module is installed in the memory slot at the bottom of your computer. There is, however, only one memory slot on the motherboard so this means that you’ll have to remove the current RAM module in order to insert a new one. The procedure to replace the memory is described below.

    1. Shut down your Netbook completely.

    2. Disconnect all external devices connected to your Samsung N315.

    3. Power off your N315 if it’s on. Also, unplug the AC power adapter.

    4. Prepare your Netbook by placing it upside-down on a flat surface with some form of soft padding. Static electricity can damage your module and other computer parts. Make sure that you are working in a static-safe environment. Remove any plastic bags or papers from your work space.

    5. Remove the battery. This will prevent you from accidentally shorting anything on the system board during this process. Slide the center battery latch into the UNLOCK position and then remove the battery.

    6. Discharge residual power by pressing the power button.

    7. Be sure to ground yourself. Touch a large piece of metal or grounded metal (like a tap) for a couple of seconds and you should be fine.

    8. Loosen the captive screw that secures the memory module compartment cover to the computer.

    9. Spread the retaining tabs on each side of the memory module slot to release the memory module. (The edge of the module opposite the slot rises away from the device). Remove the memory module by pulling the module away from the slot at an angle.

    10. Most memory will be sold in a piece of hard, clear plastic. Gently remove the new module from the packaging by pressing on it from the plastic side. Avoid bending the module or applying too much force to the packaging. When you remove the SODIMM memory module from its packaging hold it by the edges, try not to touch the gold colored contacts as this can damage the memory.

    11. Insert a new memory module into the memory slot at an angle of approximately 30 degrees aligning it to the angle of the memory slot. Memory modules are designed with a notch to prevent incorrect insertion into the memory module slot.

    12. Push the memory module down so that it’s completely fixed. If the memory does not fit easily, push the memory module down while puling the memory module latches outward. The module should be seated so that you don’t see any of the gold contacts.

    13. Before you close your case, replace the battery. Slide the battery into the battery bay and gently push until the battery locks in place as illustrated below.

    14. Test it.
    Turn your computer back on. The BIOS automatically detects the amount of memory in the system and configures CMOS accordingly during the Power-On Self-Test (POST) process. There is no hardware or software (including BIOS) setup required after the memory is installed. You should see the new amount of memory displayed on your start-up screens or in the properties for “My Computer”. The screen which appears should show approximately 2GB of RAM. The memory capacity reported in Windows is less than the actual capacity of memory. This is because BIOS or the onboard graphics uses a portion of memory or claims it for further use.

    You can also hold <F2> during the POST. When the booting screen (SAMSUNG logo) appears, press the <F2> key to enter the BIOS Setup. The BIOS Setup Utility screen will open and the System Memory item shows the total amount of memory installed in your netbook. If everything works correctly, you are done and you can close your case. If you have any problems, go to step 15 for troubleshooting tips.

    15. Troubleshooting. If you have trouble with your new RAM, check these things first. Check the power cords. Is everything plugged in properly? Check the module. Did both side clips snap to hold the module firmly in place? Try removing the module and replacing it to make sure it is seated properly in the slot. If you’re still having difficulties with your RAM, check the Crucial FAQ section. You may find an easy solution for your problem.

    16. Close the memory compartment cover and fasten the screw.

    Enjoy!

How to Upgrade RAM Memory of the Samsung N210 Pine Trail Netbook – a Complete Guide

Adding RAM is often the most cost-effective upgrade you can make to speed up a computer. When a computer runs short of RAM, it’s forced to swap the overflow data on and off of the hard drive, which can significantly slow performance. Fortunately, upgrading netbook memory is often one of the easiest computer upgrades. Do you want to get a little more power out of your Samsung N210 Pine Trail powered Netbook? Upgrade that 1GB memory module with a 2GB SODIMM. It will speed up opening new applications, running multiple applications at once, and switching between software applications (multi-tasking). Here’s a complete and easy guide on how to upgrade your Samsung N210’s memory.

Purchase the right memory.

Intel Atom N450 (Pineview) based machines can’t access more than 2GB of RAM in total. A 1GB memory module is installed in the memory slot at the bottom of your computer. There is, however, only one memory slot on the motherboard, so this means that you’ll have to remove the current RAM module in order to insert a new one. For your Samsung N210 you need a standard 200 pin DDR2 SODIMM laptop memory module (not desktop memory). Select a 2GB DDR2 SODIMM memory module of 800MHz or 667MHz. These may be referenced as PC2-6400 or PC2-5400. The 800MHz stick will work, but it won’t make a difference in speed as it’s just throttled down to the motherboard bus speed of 667MHz. Recommended brands include, but are not limited to, Crucial, Corsair, Kingston, Patriot, Hynix and Viking.

(#ad or paid links)

  • Crucial 2GB Single DDR2 667MHz (PC2-5300) CL5 SODIMM 200-Pin Notebook Memory Module CT25664AC667
    This is by far the most popular Netbook memory replacement at the moment.
  • Crucial 2GB Single DDR2 800MHz (PC2-6400) CL6 SODIMM 200-Pin Notebook Memory Module CT25664AC800
  • Corsair VS2GSDS667D2 2GB (1x2GB) DDR2 667 MHz (PC2 5300) Laptop Memory
  • A 1GB memory module is installed in the memory slot at the bottom of your computer. There is, however, only one memory slot on the motherboard so this means that you’ll have to remove the current RAM module in order to insert a new one. The procedure to replace the memory is described below.

    1. Shut down the computer completely.

    2. Power off your Samsung N210 Netbook if it’s on. Also, unplug the AC power adapter.

    3. Prepare your netbook by placing it upside-down on a flat surface with some form of soft padding. Static electricity can damage your module and other computer parts. Make sure that you are working in a static-safe environment. Remove any plastic bags or papers from your work space.

    4. Remove the battery. This will prevent you from accidentally shorting anything on the system board during this process. Pull the two battery latches outwards, then remove the battery.

    5. Discharge residual power by pressing the power button.

    6. Be sure to ground yourself. Touch something metal, like a tap, for a couple of seconds and you should be fine.

    7. The memory stick is secured in a dedicated compartment at the bottom side of your netbook.

    a. Remove the screw that secures the compartment cover using an Electronics Repair Screwdriver Set


    (#ad or paid links)
    ..

    b. Remove the compartment cover.

    8. Press outwards on the latches on both edges of the socket at the same time. Remove the SODIMM; it should pop right out. Be sure to save the old SODIMM for future use.

    9. Most memory will be sold in a piece of hard, clear plastic. Gently remove the new module from the packaging by pressing on it from the plastic side. Avoid bending the module or applying too much force to the packaging. When you remove the SODIMM memory module from its packaging hold it by the edges, try not to touch the gold colored contacts as this can damage the memory.

    10. Turn the module so the teeth are facing the SODIMM slot and the sticker is face down. It’s impossible to put the memory module in backwards thanks to the notches which “key” it with the slot. Insert the notched end of the SODIMM into the socket. This is important; you want to stick in the new memory module at a 30 degree angle. Press the SODIMM firmly, and pivot it until it snaps into place.

    11. Push the memory module down so that it’s completely fixed and the metal retaining clips clasp into the grooves on either side of the module. If the memory does not fit easily, take it out and try again. If necessary, push the SODIMM module down, while puling the memory module latches outward. The module should usually be seated so that you don’t see any of the gold contacts.

    12. Before you close your case, replace the battery. Just slide the battery into the system. The battery latches move inwards and fix the battery automatically.

    Test it.
    13. Turn your computer back on. The BIOS automatically detects the amount of memory in the system and configures CMOS accordingly during the Power-On Self-Test (POST) process. There is no hardware or software (including BIOS) setup required after the memory is installed. You should see the new amount of memory displayed on your start-up screens or in the properties for “My Computer”. Right click on the “My Computer” icon and select “properties”. The screen which appears should show approximately 2GB of RAM. The memory capacity reported in Windows is less than the actual capacity of memory. This is because BIOS or the onboard graphics uses a portion of memory or claims it for further use.

    If you don’t see approximately 2GB in “My Computer”, reboot and press F2 repeatedly until you get to the BIOS screen. It will then see the 2 Gig.

    14. If everything works correctly, you are done and you can reinstall the memory compartment cover. If you have any problems, go to step 15 for troubleshooting tips.

    15. Troubleshooting. If you have trouble with your new RAM, check these things first. Check the power cords. Is everything plugged in properly? Check the module. Try removing the module and replacing it to make sure it is seated properly in the slot. If you’re still having difficulties with your RAM, check the Crucial FAQ section. You may find an easy solution for your problem.

    16. Close the memory compartment cover and fasten te screw.

    Enjoy!