How-to upgrade your HP Mini 110’s Netbook’s memory

A memory upgrade is often the best way of increasing overall computer performance, and upgrading a HP Mini 110 Netbook is very easy, even when you’ve never done something like this before. Do you want to get a little more power out of your HP Mini 110? Upgrade that 1GB memory module with a 2GB SODIMM. It will speed up opening new applications, running multiple applications at once, and switching between software applications (multi-tasking). Here’s a complete and easy guide on how to upgrade your HP Mini 110’s memory.

Purchase the right memory. For your HP Mini 110 you need a standard 200 pin DDR2 SODIMM laptop memory module (not desktop memory). Select a 2GB DDR2 SODIMM memory module of 800 MHz or 667MHz. These may be referenced as PC-6400 or PC-5400. Recommended brands include, but are not limited to, Crucial, Corsair, Kingston, Patriot, and Viking.


Examples

Crucial 2GB Single DDR2 667MHz (PC2-5300) CL5 SODIMM 200-Pin Notebook Memory Module CT25664AC667


A 1GB memory module is installed in the memory slot at the bottom of your computer. There is, however, only one memory slot on the motherboard so this means that you’ll have to remove the current RAM module in order to insert a new one. The procedure to replace the memory is described below.

1: Shut down your Netbook completely.

2: Disconnect all external devices connected to your Mini 110.

3: Power off your Mini 110 if it’s on. Also, unplug the AC power adapter.

4: Prepare your Mini 110 by placing it upside-down on a flat surface with some form of soft padding. Static electricity can damage your module and other computer parts. Make sure that you are working in a static-safe environment. Remove any plastic bags or papers from your work space.

5: Remove the battery. This will prevent you from accidentally shorting anything on the system board during this process. Slide the battery release latches to release the battery.

6: Discharge residual power by pressing the power button.

7: If your device has WWAN capability, remove the SIM.
a) Press in on the SIM (1). The module is partially ejected from the SIM slot.
b) Remove the SIM (2) from the SIM slot.

8: Be sure to ground yourself. Touch something metal (like a tap) for a couple of seconds and you should be fine.

9: Loosen the 2 captive screws (1) that secure the memory module compartment cover to the computer.

 

10: Spread the retaining tabs (1) on each side of the memory module slot to release the memory module. (The edge of the module opposite the slot rises away from the device). Remove the memory module (2) by pulling the module away from the slot at an angle.

 

11: Most memory will be sold in a piece of hard, clear plastic. Gently remove the new module from the packaging by pressing on it from the plastic side. Avoid bending the module or applying too much force to the packaging. When you remove the SODIMM memory module from its packaging hold it by the edges, try not to touch the gold colored contacts as this can damage the memory.

12: Insert a new memory module into the memory slot at an angle of approximately 30 degrees aligning it to the angle of the memory slot. Memory modules are designed with a notch (3) to prevent incorrect insertion into the memory module slot.

13: Push the memory module down so that it’s completely fixed. If the memory does not fit easily, push the memory module down while puling the memory module latches outward. The module should be seated so that you don’t see any of the gold contacts.

14: Test it. Before you close your case, insert the SIM and replace the battery. To install the battery again, slide the battery into the system. Turn your computer back on. The BIOS automatically detects the amount of memory in the system and configures CMOS accordingly during the Power-On Self-Test (POST) process. There is no hardware or software (including BIOS) setup required after the memory is installed. You should see the new amount of memory displayed on your start-up screens or in the properties for “My Computer”. You can also Hold F10 during startup. The BIOS Setup Utility screen will open and the System Memory item shows the total amount of memory installed in your netbook. If everything works correctly, you are done and you can close your case. If you have any problems, go to step 13 for troubleshooting tips.

15: Troubleshooting. If you have trouble with your new RAM, check these things first. Check the power cords. Is everything plugged in properly? Check the module. Did both side clips snap to hold the module firmly in place? Try removing the module and replacing it to make sure it is seated properly in the slot. If you’re still having difficulties with your RAM, check the Crucial FAQ section. You may find an easy solution for your problem.

16: Close the memory compartment cover and fasten the 2 screws.

Leave a Reply