How to Upgrade your Acer Aspire One AOD250 Netbook’s RAM Memory

A memory upgrade is often the best way of increasing overall computer performance. The official manual of the 10-inch Acer Aspire One AOD250 does not say anything on upgrading your netbook, and the Acer support site isn’t much of a help either. However, upgrading a 10-inch Acer Aspire One AOD250 Netbook is very easy, even when you’ve never done something like this before. Do you want to get a little more power out of your Aspire One Netbook? Upgrade that 1GB memory module with a 2GB SODIMM. It will speed up opening new applications, running multiple applications at once, and switching between software applications (multi-tasking). Here’s a complete and easy guide on how to upgrade your Acer Aspire One AOD250’s memory.

Purchase the right memory. For your Acer Aspire One AOD250 Netbook with an Intel Atom Processor N270 or N280 you need a standard 200 pin DDR2 SODIMM laptop memory module (not desktop memory). Select a 2GB DDR2 SODIMM memory module of 667MHz. This may be referenced as PC2-5300. The PC2-5300 667MHz SODIMM is the most popular netbook memory upgrade and a faster module is backwards compatible, so a 667MHz SODIMM will definitely work, even when the original SODIMM is a 533MHz module. Recommended brands include, but are not limited to, Crucial, Corsair, Kingston, Patriot, and Viking.


Examples

Crucial 2GB Single DDR2 667MHz (PC2-5300) CL5 SODIMM 200-Pin Notebook Memory Module CT25664AC667


A 1GB memory module is installed in the memory slot at the bottom of your computer. There is, however, only one memory slot on the motherboard so this means that you’ll have to remove the current RAM module in order to insert a new one. The procedure to replace the memory is described below.

1: Shut down your Netbook completely.

2: Disconnect all external devices connected to your Aspire One AOD250.

3: Power off your AOD250 if it’s on. Also, unplug the AC power adapter.

4: Prepare your Netbook by placing it upside-down on a flat surface with some form of soft padding. Static electricity can damage your module and other computer parts. Make sure that you are working in a static-safe environment. Remove any plastic bags or papers from your work space.

5: Remove the battery. This will prevent you from accidentally shorting anything on the system board during this process. To remove a battery pack:
1 Slide the battery release latch to release the battery.
2 Pull the battery from the battery bay.

6: Discharge residual power by pressing the power button.

7: If your device has WWAN capability, remove the 3G SIM card (only for certain models).

8: Be sure to ground yourself. Touch something grounded metal (like a tap) for a couple of seconds and you should be fine.

9: Loosen the captive screw that secures the memory module compartment cover to the computer.

10: Spread the retaining tabs on each side of the memory module slot to release the memory module. (The edge of the module opposite the slot rises away from the device). Remove the memory module by pulling the module away from the slot at an angle.

11: Most memory will be sold in a piece of hard, clear plastic. Gently remove the new module from the packaging by pressing on it from the plastic side. Avoid bending the module or applying too much force to the packaging. When you remove the SODIMM memory module from its packaging hold it by the edges, try not to touch the gold colored contacts as this can damage the memory.

12: Insert a new memory module into the memory slot at an angle of approximately 30 degrees aligning it to the angle of the memory slot. Memory modules are designed with a notch to prevent incorrect insertion into the memory module slot.

13: Push the memory module down so that it’s completely fixed. If the memory does not fit easily, push the memory module down while puling the memory module latches outward. The module should be seated so that you don’t see any of the gold contacts.

14: Test it. Before you close your case, insert the SIM and replace the battery. To install the battery again, slide the battery into the system. Turn your computer back on. The BIOS automatically detects the amount of memory in the system and configures CMOS accordingly during the Power-On Self-Test (POST) process. There is no hardware or software (including BIOS) setup required after the memory is installed. You should see the new amount of memory displayed on your start-up screens or in the properties for “My Computer”. You can also hold <F2> during the POST; while the notebook PC logo is being displayed. The BIOS Setup Utility screen will open and the System Memory item shows the total amount of memory installed in your netbook. If everything works correctly, you are done and you can close your case. If you have any problems, go to step 13 for troubleshooting tips.

15: Troubleshooting. If you have trouble with your new RAM, check these things first. Check the power cords. Is everything plugged in properly? Check the module. Did both side clips snap to hold the module firmly in place? Try removing the module and replacing it to make sure it is seated properly in the slot. If you’re still having difficulties with your RAM, check the Crucial FAQ section. You may find an easy solution for your problem.

16: Close the memory compartment cover and fasten the screw.

17: Insert your 3G SIM card if you have one.

Leave a Reply